Autowatch Ghost Immobiliser Installation
The Ghost is the UK's most advanced aftermarket immobiliser for CAN bus. It is discreet It does not include LED indicators or key fobs and is hidden within the vehicle's wiring.
The user can also deactivate the system temporarily using Transport Mode when renting out their car. This guide will take you through the steps of installing the Ghost immobiliser.
Professional Installation
The Autowatch Ghost immobiliser protects your car against key hacking attacks, cloning and relay attacks. The system is directly connected to the ECU of your vehicle and protected by a pin code you select. It is not detected by thieves using diagnostic scanners or other advanced methods. It isn't able to be disabled with circuit cuts.
The system is easy to use, but professional installation is recommended to ensure a smooth connection to the ECU of your vehicle. Installers who are approved by Thatcham can assist you with the installation and programing of your Ghost system. They can also recommend an alarm or tracking system to complete the protection package for your vehicle.
To avoid the accidental deployment of airbags or short circuits The installer must first disconnect your battery. Once the battery is disconnected, the installer may be able to work safely. Hand tools are essential for securing connections with precision and a multimeter may be used to check the electrical properties and safety. Insulation tape and cable tie are essential to protect connections and keep wiring neat. The Ghost Immobiliser user's manual will provide specific instructions specifically tailored to your specific model.
It is crucial to select a grounding location that is free of any paint or debris during installation. Installers must also ensure that the immobiliser's wires CAN H & can L are connected to the correct ECU ports. Based on the model, these wires may need to be soldered or plugged in. To ensure a stable and long-lasting connection it is recommended you choose a top-quality plug.
Transport Mode can be activated by the customer after the installation is completed. This permits mechanics or valet parking to use the vehicle, without knowing the pin code. The user must press the service icon on the dashboard five times over two seconds. Once this is done the system will confirm with 5 signal indicators.
The Autowatch Ghost 2 is a highly effective immobiliser that's TASSA certified and Thatcham approved. It's a smart choice for anyone who frequently rents their vehicle on platforms such as Turo. have a peek at these guys can lower the cost of insurance, as it decreases the likelihood of theft.
Getting Started
It's not difficult to come up with an autowatch ignition device in order to guard your vehicle from theft. It will stop your car from being started even when a criminal steals or copies the key. It's possible due to its advanced technology that stops the engine from starting until the right PIN code is entered.
The device is connected to the vehicle's bus system CAN, allowing direct communication with the ECU. It makes use of the buttons on your dashboard and steering wheel to create a unique sequence, which only you know. This makes it impossible for anyone else to start your car. This is the best security system that protects your most precious possessions and will ensure its value in the event that you decide to sell it in the future.
Installing a ghost ignition is an easy procedure, but it is important to follow the instructions carefully to avoid problems with the electrical system and malfunctions. You'll need to find a 12V power source and a suitable grounding for the chassis of your car. After that, you are able to begin to connect the wires that will be used to activate the immobiliser. Make sure you use top-quality connectors and soldering methods to ensure a secure connection. Also, make sure to insulate the connections with heat shrink tubing or insulation tape to shield them from electrical short circuits and other issues.
After the wires have been connected, you can reconnect the battery and turn on the engine to test the function of the immobiliser. When everything is functioning correctly then you can put it in a safe location under the dash or somewhere else in the vehicle. Be sure to hide it in a secure manner to ensure that thieves cannot alter it.
The Ghost 2 immobiliser is TASSA (Tracker and Aftermarket Security System Association) verified This means it is in compliance with the highest standards of security and is a great deterrent to car thieves. It is invulnerable to key cloning and hacking and cannot be disabled without the code. The device is also easy to use and can be put into an auto valet mode so that your vehicle isn't activated if you take it in for servicing or an MOT.
Wiring
The Ghost Immobiliser is a cutting-edge security system designed to stop theft of vehicles. It connects directly to the vehicle's CAN bus and communicates with the ECU and ECU, making it virtually undetectable as an addition to your vehicle. The Ghost Immobiliser will not interfere with your vehicle's factory settings, unlike other aftermarket systems that require the removal of circuit elements.
It's also completely undetectable to thieves using diagnostic scanners. The system doesn't send or receive radio frequency signals and instead uses CAN data to communication with your ECU. Additionally, it doesn't require any modifications to your vehicle's existing key fobs.
Enter your disarm sequence (either two or one buttons) and then switch on the ignition of your vehicle to activate the Ghost Immobiliser. The indicator will flash two times to confirm that you have entered the correct code. Once you've verified this, you're able to start your car and drive away with peace of mind.
Once installed The Ghost Immobiliser can secure your vehicle from key cloning and hacking while preserving the value of your pride and joy. If you ever have to surrender your vehicle for service or valet parking The Ghost Immobiliser will be temporarily disabled in Transport Mode.
You'll require a constant power source (12V) in addition to a grounding point to complete the installation of a Ghost immobiliser. Make sure that both are well-insulated and can be touched. It is also recommended to use cable ties to tie and secure the wires, since this reduces the risk of theft by thieves. To avoid making mistakes, make sure to double-check these points and mark them using a label or tape. Check all connections for signs that they're getting worn out. Be sure to ensure that all connections are securely in place, and properly insulated. Don't forget to test your Ghost Immobiliser after installation has been completed. This will confirm that the unit is operating properly and that all connections and insulation are safe. Make sure to address any issues immediately.
Testing
The Autowatch Ghost immobiliser is a revolutionary vehicle security system that works seamlessly with your car's ECU in order to prevent unauthorised motor starting. Its innovative technology safeguards your vehicle against hacking and key cloning and other methods employed by thieves to steal vehicles. The Ghost also works in tandem with other alarm and tracking systems to give the most complete protection for your vehicle. This system's unmatched features and discreet design make it a popular option for car enthusiasts and security-conscious drivers alike.
It is essential to follow the procedures for installation to ensure the correct integration of the Ghost Immobiliser. The best way to begin is to look over the vehicle's wiring diagram that will serve as a guideline for locating and connecting the necessary wires. After that, you'll need identify the power source as well as grounding points. Once you've identified these, you'll have to mark them in a way that they're easy to identify during the installation process. It's important to use high-quality materials and tools. Hand tools are a must to make precise connections while a multimeter can check electrical values and ensure security. Cable tie and insulation tape will ensure that all connections are tidy. A Ghost-specific user's guide is also available.
Before you begin installing, it's important to test the system by entering the PIN code and then starting the vehicle. This test will verify that the immobiliser works as intended and prevent unauthorised vehicle starts. It is recommended to complete this routinely as part of your routine inspections of the vehicle to ensure the system is always functioning properly.
Once the installation has been completed, you are now able to start driving your vehicle with confidence. The Ghost will keep your car and its contents safe from would-be thieves, ensuring that nobody can escape with your car without the proper PIN code. The Ghost can be paired with an approved Thatcham tracker, which detects attempts at theft or tampering. This lets you track your vehicle if it is stolen.
The Ghost is compatible with a wide variety of vehicles, including those made by all major manufacturers. If you are interested in protecting your car with this cutting-edge device, contact Monty's Locksmith today to find out more about our installation and service options. We are a TASSA Registered installer, a certification that guarantees that we follow strict standards and procedures for installing our products. This assures customers, insurance companies and law enforcement officials that installations are done safely and in a correct manner.